DCT4 Direct Box for repairing IMEI on Nokia phones

This is the first standalone software that can repair IMEI/ESN number of a Nokia DCT4 phones to any digit without UEM change.

This software allows you to:
- Repair IMEI on DCT4 phones without opening the phone (UEM Change)

About DCT4 Direct Software:
- Works on Window XP
- Future updates and support
- Real USB data transfer between PC and Phone
- Best Quality phone Cables and Software

How its works:
On all Nokia DCT4 phones the important security data for the IMEI and ESN is stored on a special, not rewritable chip inside the phone: the UEM chip. This chips characteristic is that it is only one time programmable (OTP) and that the data inside cannot be rewritten. Because of this, until now it was only possible, to repair the IMEI/ESN if you change this UEM chip. Since this task requires a lot of time and effort, a lot of customers were looking for an easier solution, without the need to open the phone and change some components inside. And after some time finally somebody created a tool that was able to do all that operations without changing the UEM chip: the DCT4 DIRECT Box. This software uses a special technique in order to make it possible to repair the IMEI/ESN without changing any data on the UEM chip it self. This task is done by editing the MCU Firmware inside the phone and writing the desired IMEI/ESN data to the FLASH, not to the UEM chip, this procedure is also known as FLASH PATCHING. After the phone has been updated with the patched flash data by the DCT4 DIRECT BOX the phone will have the new IMEI/ESN number and all simlock data rebuild as well. This might sound a little bit complicated now, but in fact the user is not affected in any way by this procedure. All the user need to do is to type the desired IMEI/ESN number into a field and then just press one button for starting the IMEI/ESN repair.

Support phone models:
DCT4 Direct (v1.0.0.32):

- NHM-7 - 8310, v 6.20
- RH-19 - 3100, v 5.91
- NHL-6 - 6800, v 3.14
- RH-9 - 3510i, v 5.35
- RM-17 - 7260, v 3.36
- NEM-1 - 3300, v 4.62
- NPL-2 - 6100, v 5.80
- RH-23 - 7200, v 4.26
- NHL-4J - 7250, v 3.62
- NPE-4 - 6310, v 5.10
- NHL-4 - 7210, v 5.63
- NPL-1 - 6310i, v 7.00
- RH-37 - 3220, v 3.60
- RM-37 - 6610i, v 4.10
- NHM-8 - 3510, v 5.02
- RH-30 - 3200, v 5.29
- NHL-4JX - 7250i, v 5.30
- NKC-1 - 2270, v 9.07
- NPC-1 - 3320, v 4.00
- NPW-1PA - 3361*, v 3.06
- RH-17R - 2280, v F175V0500.nep
- DTE-1 - D211*, v 4.01
- RH-18 - 1100*, v 5.62
- NPM-10 - 3595, v 8.18
- NKC-1 - 1220, v 9.07
- NPD-1AW - 3585, v B100V0557.nep
- RH-44 - 3586, v D100V0112.nep
- RH-3 - 2285, v G101V0801.nep
- NPM-8 - 3590, v 7.64
- RM-12 - 7710, v Vp2.200
- RA-2 - 9500, v 3.35.2
- RH-38 - 1100a*, v 5.62
- NHL-9 - 6820a, V 4.25
- RAE-6 - 9300, v 3.06
- RH-48 - 3105, v J175V0300.nep
- NPL-3 - 6200, v 4.22
- RH-27 - 6225, v H190V0800.nep
- RH-50 - 3100b, v 4.03

Note:
The Supported Phones above marked with Star (*) sign do not operate properly with this version. Do not use them. In case you do and have a dead phone, just reflash the MCU to repair it (1100 - MCU+PPM).

IMPORTANT:

* Please note that the DCT4 DIRECT BOX cannot work with phones that:
- Have bad UEM data (30 sec off problem)
- Don't have any UEM data at all (?????????????? IMEI/ESN)
- Have Software/Hardware problems
- Please always check if phone is in full working condition before starting the IMEI/ESN repair procedure.
- If you want to bring the phone back to its original state, then you only need to flash the phone with original MCU software. After MUC software update the patch will be erased and the phone will operate as before.
- IMEI changing is illegal in some countries. All procedures you might accomplish with this box are full responsibility of the user, not the supplier.

Package Contains:

- DCT4 DIRECT USB BOX
- USB power cables
- Cd with DCT4 Direct Software
- Complete Set Cable (46 Cables)
NK1100, NK2280, NK2650, NK3200, NK3220, NK3230, NK3300, NK3310, NK3320, NK3360, NK3510, NK3650, NK5100, NK5140, NK6100, NK6101, NK6170, NK6230, NK6260, NK6340, NK6600, NK6620, 6630 with battery pin, NK6650, NK6680 with battery pin, NK6800, NK6820, NK7200, NK7210, NK7260, NK7280, NK7600, NK7610, NK7650, NK7710, NK8310, NK8800, NK8850, NK8910, NK9300, NK9500, NGAGE, NG-QD, NKI N90, NKI N70, JAF MMC Card Cable